klioncre.blogg.se - Hunter air conditioning control panel manual

HUNTER AIR CONDITIONING CONTROL PANEL MANUAL MANUAL
HUNTER AIR CONDITIONING CONTROL PANEL MANUAL UPGRADE
HUNTER AIR CONDITIONING CONTROL PANEL MANUAL PROFESSIONAL

Locate the MANUAL CONTROL button on the right-hand side of the unit.ģ. Open the front panel of the indoor unit.Ģ.

Unit must be turned off before manual operation.ġ. To restore regular operation, use the remote control to activate the unit. Please do not use this function unless the remote control is lost and it is absolutely necessary. The sleep feature will stop after 8 hours and the system will keep running.ĬAUTION The manual button is intended for testing purposes and emergency operation only. When in HEAT mode, the unit will decrease the temperature by 2☏ (1☌) after 1 hour, and will decrease an additional 2☏ (1☌) after another hour. When in COOL mode, the unit will increase the temperature by 2☏ (1☌) after 1 hour, and will increase an additional 2☏ (1☌) after another hour. Press the SLEEP button when you are ready to go to sleep. And the Sleep function is not available in FAN or DRY mode. This function can only be activated via remote control. The SLEEP function is used to decrease energy use while you sleep. The indoor unit will automatically display “EC” or “EL0C”or flash LEDS (model dependent ) when it detects refrigerant leakage Refrigerant Leakage Detection (some units).When turning on your unit, the louver will automatically resume its former angle.

HUNTER AIR CONDITIONING CONTROL PANEL MANUAL PROFESSIONAL

For the USB device access, replacement, maintenance operations must be carried out by professional staff. Wireless control allows you to control your air conditioner using your mobile phone and a wireless connection. When turning off the unit from COOL, AUTO (COOL), or DRY modes, the air conditioner will continue operate at very low power to dry up condensed water and prevent mildew growth. If the unit loses power, it will automatically restart with the prior settings once power has been restored. Not all the functions are available for the air conditioner, please check the indoor display and remote control of the unit you purchased. Regularly inspect and clean air filters.Ī guide on using the infrared remote is not included in this literature package.Limit energy usage by using TIMER ON and TIMER OFF functions.To further optimize the performance of your unit, do the following: Please set the vertical air flow louver to its maximum angle (vertically to the floor), and set HIGH fan mode. If the air conditioner operates in excess of this figure, the surface of the air conditioner may attract condensation. NOTE: Room relative humidity less than 80%. When outside temperature is below 32☏ (0☌), we strongly recommend keeping the unit plugged in at all time to ensure smooth ongoing performance. When your air conditioner is used outside of the following temperature ranges, certain safety protection features may activate and cause the unit to disable.įOR OUTDOOR UNITS WITH AUXILIARY ELECTRIC HEATER User manual of Cooper&Hunter CH-NG09MIA115VI (20 pages) Operating temperature SUBMITTAL DATA SHEET CH NG09MIA115VI:O - (English).

HUNTER AIR CONDITIONING CONTROL PANEL MANUAL UPGRADE

Is it time to upgrade your thermostat? Use our thermostat upgrade guide to help you make the right choice for your needs.Cooper&Hunter CH-NG09MIA115VI - Cooling and Heating Solutions - Use Manual - Use Guide PDF. Locate the Installation and User Manualsįor your product and confirm the thermostat is correctly configured for your equipment’s system type and

Confirm the thermostat has been correctly configured for your system.

The installation guide for your thermostat will show which one you have. On some thermostats, this connection is madeīy a jumper wire connection on other models this connection is made by a slider switch that has 1-wire andĢ-wire settings. Separate wires to R and Rc, these terminals must be connected.

Verify that the wiring was matched correctly from the old thermostat to the new thermostat.

If this is a new installation or the first time you’ve set your thermostat to cooling since it was installed: If the cooling still doesn't come on, but has worked in the past, call a professional HVAC contractor to assist you. Verify these wires are firmly connected to the correct terminals.

In most cases, your thermostat turns on the compressor and fan (Y and G terminals/ wires) during cooling.

Make sure the furnace circuit breaker switches are on.

If the thermostat is set for cool, verify that the furnace door is securely closed and that the furnace’s power.

Icons are flashing, the thermostat is in delay mode, which can last up to 5 minutes.

Check the thermostat display for cooling, usually indicated by the words “cool on” or a snowflake icon.

Verify that the thermostat is switched to cool mode and has a cooling set point below the room temperature reading.

If you’re signed up for a Saver’s Switch through your utility company or a Demand Response program, your AirĬonditioning compressor may be cycling off for longer intervals.